Ball, Rod & SAG Mills

Used/refurbished 17’ dia x 5’ long autogenous mill

  • Manufactured by Aerofall (now Polyisus)
  • 20”wide x 83” dia., shoe style bearings
  • 4 piece ring gear, spur cut, 248 teeth
  • Feed chute
  • Gear guards
  • 3 Spare pinions
  • Cylindrical Shell with removable heads
  • CJT Reference – DS#03910

2 Used 13 X 20.5 ball mills

  • Manufactured by Allis Chalmers
  • 1750 Hp
  • Gear reducer and clutch
  • Rubber liners
  • Gear and bearing lube systems
  • Feed chute
  • Trommel discharge
  • CJT Reference DS#08656

1 used 8’ dia. x 10’ long, Allis Chalmers Ball Mill

  • Wet grind, grate discharge, spout feed
  • Single helical gear ring and pinion drive with gear guard
  • Gear spray lubrication system
  • Main bearing lubrication system
  • Existing rubber liners
  • 400 hp induction motor, 1800 rpm, 3ph/60Hz/575 volt
  • Voith fluid drive coupling and Moventas gear reducer
  • CJT Reference DS#8657

1-Used 9×10 Allis Chalmers Ball Mill

  • Wet grind, trommel discharge
  • Single helical gear ring and pinion drive with gear guards
  • 400 hp synchronous motor, 3ph/60Hz/5550 volt
  • Eaton 20VC1000 Pneumatic clutch
  • Bearing lubrication pumps
  • CJT Reference DS#08753

Crushers

1 – used 32″ x 44″ Telsmith Jaw Crusher

  • Overhead Eccentric
  • Manufactured 2012
  • Lubrication system
  • Hydraulic adjustment and relief
  • CJT Reference DS#08755

1 – used Vertical Shaft ImpactCrusher

  • Barmac Model B5100SE
  • Manufactured by Metso
  • 75 HP – 3/60/575v-3560rpm
  • Mounted on stand
  • CJT Reference DS#08757

1 – used/refurbished 18” x 24” McLanahan single roll crusher

  • Cobra model
  • Toothed roll
  • new countershaft & roll shaft bearings
  • Tramp iron release
  • V-belt sheave
  • CJT Reference DS#08736

1 – used 6659 Raymond Roller Mill

  • 66″ Grinding Ring with 5 rolls
  • Double Whizzer Separator
  • Direct-Fired Air Heater
  • 200 HP Mill Drive
  • 534 original hours
  • Electrical Controls and Switchgear
  • Spencer Blower
  • CJT Reference DS#08718

1 – Refurbished 6669 Raymond Roller Mill

  • 66″x 9″ Grinding Ring with 6 rolls
  • Mill base with air and mill side housing
  • Exhauster
  • Completely disassembled and rebuilt
  • List of new parts and repairs available
  • Electrical Controls and Switchgear
  • CJT Reference DS#08754

1 – Refurbished 5458 Raymond Roller Mill

  • 54″x 8″ Grinding Ring with 6 rolls
  • Mill base with air and mill side housing
  • Exhauster
  • 7’diameter double whizzer
  • 9’diameter cyclone
  • Completely disassembled and rebuilt
  • List of new parts and repairs available
  • Electrical Controls and Switchgear
  • CJT Reference DS#08756

1 – Used Alpine U500 Pulverizer

  • Manufactured by Alpine (now Hosakawa)
  • Model U500
  • Feed throat with Magnet
  • 60 HP Drive
  • CT Reference DS#08749

Lab and Sample Equipment

Sample Preparation Crushers

  • 3″ x 5″ Woodstock Jaw Crusher
  • Bico Braun DiscPulverizer
  • Both mounted on Common Table
  • Motor: 3HP & 2HP (3/60/575v)
  • Cabling and Switches
  • CJT Reference DS#08640

1- Used Ring adn Puck Pulverizer

  • MFD by T.M. Engineering
  • Sound attenuation Cabinet
  • Two sizes of bowls and rings
  • Motor: 1HP (3/60/575v)
  • Clamping
  • CJT Reference DS#08637

Mill and Crusher Parts

1 – Used integral pinion and shaft

  • Herringbone
  • 25″ Face width
  • 31 teeth
  • Approximately 84” long
  • 7–5” dia. shaft
  • 2” x 9.5” key way
  • From a 10’ dia x 15’ Dominion Engineering rod mill